Auto hydraulic dough divider/bread dough cutter for sale

Product Application of Auto hydraulic dough divider/bread dough cutter for sale

1. Usage of Hydraulic Dough Divider

The Hydraulic Divider can be used to divide large dough into 20pcs with the same weight division, and the inside structure is close-grained. It can save labour cost and avoid division difference by hand.

2.Technician Data of Auto hydraulic dough divider/bread dough cutter for sale

Main Features for Hydraulic Dough Divider

1.Divide the dough into same weight per pcs division. 

2.Operate easily.

3.Machine strong with long life

4.Save time, only 10~20seconds per operating time for large production

5.Clean easily.

Note: Weight depends on the dough condition, Less weight, lower quality of side. Dough can't be too soft or hard, otherwise, the quality is not good.

Installation of Auto hydraulic dough divider/bread dough cutter for sale

1. Choose dry, flat floor without direct sunshine and hot source

2.Connect the correct power supply with 380V+N+PE, and 3hase, 10A breaker.

3.Open the cover, take out 4pcs plastic tube, use vegetable oil to clean the surface of the cutter and pump.


Operation of Auto hydraulic dough divider/bread dough cutter for sale

1.Connect the power supply and need to connect with ground.

2.Push the "down" button to move the cutter base and cutter to lowest position, put some vegetable oil on the surface.

3.Load the dough(Max weight 16kgs), and put some vegetable oil on the dough surface.

4.Close the top cover, tighten the top handle.

5.Push the "up" button to finish pressing, dividing.

6.Open the cover, push "down" button to raise cutter base, and take out the division dough.

Cleaning and Maintenance

1. After usage, you should clean the pump, cutter base, cutter, inside surface of top cover. Use cloth to dip vegetable oil to clean. Please use sunflower oil, olive oil. Salad oil not allowed.

How to clean cutter base and cutter:

Open the top cover, put 4 plastic tubes upright on the surface of the cutter base. Note: it can't be put on the cutter.

Close the top cover, push "up" button to raise the cutter, while the cutter base on the lowest position, and the cutter on the highest position, then cut off power supply, open the cover, clean the cutter and cutter base.

1.Every week, please clean the machine outside with sponge with soap water, not directly by water.

2. Every week, please clean machine inside. 

Pull the machine, cleaning same as cutter and cutter base, let the cutter base on the lowest position, cutter on the highest position. Open the side panel, you can see the machine inside. Cut off power supply, use brush to clean all corners to remove the dough and flour. 

3.Every 3 months check the hydraulic oil meter of hydraulic unit.

Let he cutter base, cutter to the lowest position, cut off power supply, then pull the machine, open the side panel, and you can see the hydraulic unit. Open the lid of hydraulic unit, use oil meter or clean screwdriver to check if there is 2cm oil, if less, you have to add more.

Hydraulic oil type: ConDAT HYDRAULUB S46 GRAD 46 or similar grade.


Notice

1.cut off power supply when loading, taking out dough, and cleaning.

2.Use correct hydraulic oil and clean vegetable oil.

3.4 pcs plastic tubes for cleaning not allowed to put on the cutter.

Machine Parts

the whole frame of the dough divider through integral cast forming,

luxury, stable and durable.

Division Range And pcs

The weight range of dough is 100-800g ,can divide 20 pieces at one time.

uniform division,the dough error is within 3 grams.

only 10~20seconds per operating time for large production
 

Machine Parts

manual control button,easy to operate,convenient and low failure rate.

Hydraulic system

Using advanced liquefaction block system

FQA for Hydraulic Dough Divider

Q1.What Methods of Payment Are Acceptable? 

1. Telegraphic Transfer (T/T): we accept 30% T/T deposit before production and 70% T/T Balance before shipment. 100% payment for sample orders. 

2. Western Union: we accept 100% payment via the western union. 

3. Letter of Credit (L/C): we accept 100% L/C irrevocable at sight. 



Q2. What Is the Cost of Shipping? 

Shipping cost is based on the following elements: 

1.Number of packages 2. Gross Weight 3. Package CBM 4. Destination port 

We can arrange shipping for you , if you have shipping agent in China , we can send goods to your warehouse . 



Q3. How about the Delivery Time? 

Some of the products are in stock at our warehouse, generally we need 3~5 days to change the plugs before the delivery. Regarding to the non-stock products, the lead time 15-30 days depends on your requirement on the product.